Isolation and cultivation of astrocytes from adult mouse brain
This application protocol describes the generation of highly purified and viable astrocytes from adult mouse brain tissue. Brain tissue from mice older than P7 is dissociated into single-cell suspensions using the Adult Brain Dissociation Kit, mouse and rat. The extracellular matrix is enzymatically digested using the kit components, while the gentleMACS® Dissociator with Heaters is used for the mechanical dissociation steps during the on-instrument enzyme incubation. After the dissociation, myelin and cell debris are removed using Debris Removal Solution, followed by a removal of erythrocytes using Red Blood Cell Removal Solution (10×). The Anti-ACSA-2 MicroBead Kit is used to isolate astrocytes from the single-cell suspension.
Protocol
Isolation and cultivation of astrocytes from adult mouse brain
45 min
Dissociation of brain tissue
1 h
Isolation of astrocytes
30 min
Flow cytometric analysis
7 d
Cell culture
1 h
Immunocytochemical staining of cultured cells
It is recommended to analyze the separated cells by flow cytometry prior to cultivation. Adjust cell culture time to meet experimental objectives.
Isolation and cultivation of astrocytes from adult mouse brain
- For subsequent cell separation and cultivation, it is recommended to dissociate at least 800 mg of adult mouse brain tissue.
- Volumes given below are for one adult mouse brain (max. 500 mg) in 1980 μL enzyme mix. When working with less than 500 mg, use the same volumes as indicated. When working with higher amounts, scale up all reagent volumes and total volumes accordingly. A maximum of 500 mg brain tissue per tube can be processed.
- A swinging bucket rotor is recommended for centrifugation, e.g., Heraeus® Multifuge 4KR by Thermo Fisher® Scientific.
Preparation of Adult Brain Dissociation Kit, mouse and rat
- Enzyme P is ready to use. Prepare aliquots of appropriate volume to avoid repeated freeze-thaw-cycles. Store aliquots at –20 °C. This solution is stable for 6 months. Resuspend the lyophilized powder in the vial labeled Enzyme A with 1 mL Buffer A. Do not vortex. This solution should be aliquoted and stored at –20 °C for later use. Avoid repeated freeze-thaw-cycles.
- Prepare enzyme mix 1 and enzyme mix 2 according to the table below.
Table 1: Volumes for preparation of enzyme mixes.
| Enzyme mix 1 | Enzyme mix 2 | ||
| Enzyme P: 50 µL | Buffer Z: 1900 µL | Buffer Y: 20 µL | Enzyme A: 10 µL |
Preparation of 1× Red Blood Cell Removal Solution
- Dilute Red Blood Cell Removal Solution (10×) 1:10 with double-distilled water (ddH2O), for example, dilute 0.1 mL of cold Red Blood Cell Removal Solution (10×) with 0.9 mL cold ddH2O.
▲ Note: Do not use deionized water for dilution. - Store the prepared 1× Red Blood Cell Removal Solution at 2–8 °C. Discard unused solution at the end of the day.
Preparation of AstroMACS Medium and cell culture dish
- Start preparation of AstroMACS Medium by thawing MACS® NeuroBrew®-21 at 2–8 °C prior to use.
- Reconstitute lyophilized Astro MACS Supplement with 1 mL MACS Neuro Medium.
▲ Note: Single-use aliquots of the reconstituted AstroMACS Supplement can be stored at –20 °C. It is recommended to prepare aliquots of 100 μL. - To obtain the complete medium, add 0.2% of the reconstituted AstroMACS Supplement, 2% of the MACS NeuroBrew-21, 50×, and 0.25% L-glutamine (0.5 mM) to the MACS Neuro Medium, e.g., 100 μL AstroMACS Supplement, 1 mL MACS NeuroBrew-21, and 125 μL L-glutamine to 50 mL MACS Neuro Medium.
- Use the complete medium within two weeks when stored at 2–8 °C. Do not freeze.
- Coat the culture dish (24-well plate) with 0.01% poly-L-lysine overnight at 37 °C. After washing three times with ddH2O, coat the plate overnight at 37 °C with 10 μg/mL laminin. Wash again three times with ddH2O. Let the culture dish dry under sterile conditions.
Tissue dissociation
- For details on the use of the gentleMACS Octo Dissociator with Heaters, refer to the user manual.
- A maximum of one mouse brain (max. 500 mg) in 2 mL enzyme mix can be processed in one C Tube.
- For dissociation of small amount of neural tissue (<100 mg), refer to data sheet of Adult Brain Dissociation Kit, mouse and rat.
For cell culture experiments subsequent to tissue dissociation, all steps should be performed under sterile conditions.
- Remove the mouse brain. Wash the brain in cold D-PBS.
- Prepare the appropriate volume of enzyme mix 1 (see table 1) and transfer it into a gentleMACS C Tube.
- Place the brain on a petri dish and cut it into eight sagittal slices using a scalpel.
- Transfer the tissue pieces into the C Tube containing 1950 μL of enzyme mix 1.
- Transfer 30 μL of enzyme mix 2 into the C Tube.
- Tightly close the C Tube and attach it upside down onto the sleeve of the gentleMACS Octo Dissociator with Heaters.
- Run the gentleMACS Program 37C_ABDK_01.
- After termination of the program, detach the C Tube from the gentleMACS Octo Dissociator with Heaters.
- (Optional) Centrifuge briefly to collect the sample at the bottom of the tube.
- Resuspend sample and apply it to a MACS SmartStrainer (70 μm) placed on a 50 mL tube.
▲ Note: Moisten MACS SmartStrainer with buffer before use.
▲ Note: When upscaling the reagent volume and total volumes, increase also the number of MACS SmartStrainers (70 μm). One MACS SmartStrainer (70 μm) can be used for one adult mouse brain.
▲ Note: Cells with a diameter of >70 μm may be lost. To obtain these cells within the flow-through, use a cell strainer with an appropriate mesh size. - Apply 10 mL of cold D-PBS onto the MACS SmartStrainer (70 μm).
- Discard MACS SmartStrainer (70 μm) and centrifuge cell suspension at 300×g for 10 minutes at 4 °C. Aspirate supernatant completely.
- Proceed to section "Debris and red blood cell removal".
Debris and red blood cell removal
- Volumes given below are for the cell suspension from up to two adult mouse brains (max. 1 g) as starting material. When working with higher tissue quantities, scale up all reagent volumes accordingly.
- The cell suspension from two adult mouse brains (max. 1 g) is the maximum that can be processed in one 15 mL reagent tube.
- Always use pre-cooled buffers and solutions (4 °C).
Table 2: Volumes for debris removal.
| Debris Removal Solution | D-PBS | Overlay (D-PBS) | |
| 1 brain (400-500 mg) | 900 µL | 3100 µL | 4 mL |
| 2 brains (800-1000 mg) | 1800 µL | 6200 µL | 4 mL |
- Resuspend cell pellet carefully with the appropriate volume of cold D-PBS according to table 2 and transfer cell suspension to a 15 mL tube. Do not vortex.
- Add appropriate volume of cold Debris Removal Solution.
- Mix well.
- Overlay very gently with 4 mL of cold D-PBS.
▲ Note: Pipette very slowly to ensure that the D-PBS phase overlays the cell suspension and phases are not mixed. - Centrifuge at 4 °C and 3000×g for 10 minutes with full acceleration and full brake.
▲ Note: If the centrifugation is suboptimal, acceleration and brake can be reduced. - Three phases are formed. Aspirate the two top phases completely and discard them.
- Fill up with cold D-PBS to a final volume of 15 mL.
- Gently invert the tube three times. Do not vortex.
- Centrifuge at 4 °C and 1000×g for 10 minutes with full acceleration and full brake. Aspirate supernatant completely.
- Resuspend cell pellet from up to two adult mouse brains carefully in 1 mL of cold 1× Red Blood Cell Removal Solution. Do not vortex.
- Incubate for 10 minutes in the refrigerator (2−8 °C).
- Add 10 mL of cold D-PBS/BSA buffer.
- Centrifuge at 4 °C and 300×g for 10 minutes. Aspirate supernatant completely.
- Proceed to section "Isolation of astrocytes".
Magnetic labeling
- Work fast, keep cells cold, and use pre-cooled solutions. This will prevent capping of antibodies on the cell surface and non-specific cell labeling.
- Volumes for magnetic labeling given below are for up to 1×107 total cells. When working with fewer than 1×107 cells, use the same volumes as indicated. When working with higher cell numbers, scale up all reagent volumes and total volumes accordingly (e.g., for 2×107 total cells, use twice the volume of all indicated reagent volumes and total volumes).
- For optimal performance, it is important to obtain a single-cell suspension before magnetic labeling. Pass cells through 70 µm nylon mesh (e.g. MACS SmartStrainer (70 µm)) to remove cell clumps which may clog the column. Moisten filter with buffer before use.
- The recommended incubation temperature is 2–8 °C. Higher temperatures and/or longer incubation times may lead to non-specific cell labeling. Working on ice may require increased incubation times.
- Resuspend cell pellet in 80 µL of AstroMACS Separation Buffer.
- Add 10 µL of FcR Blocking Reagent.
- Mix well and incubate for 10 minutes in the dark in the refrigerator (2−8 °C).
- Add 10 µL of Anti-ACSA-2 MicroBeads.
- Mix well and incubate for 15 minutes in the dark in the refrigerator (2−8 °C).
- Wash cells by adding 1 mL of AstroMACS Separation Buffer and centrifuge at 300×g for 5 minutes. Aspirate supernatant completely.
- Resuspend up to 1×107 cells in 500 µL of AstroMACS Separation Buffer.
▲ Note: For higher cell numbers, scale up buffer volume accordingly. - (Optional) Take 20 µL for later flow cytometric analysis (original fraction).
- Proceed to section "Magnetic separation".
Magnetic separation
Magnetic separation with MS Columns
- Choose an MS Column and an appropriate MACS Separator. For details refer to tab "Materials".
- Always wait until the column reservoir is empty before proceeding to the next step.
- Degas buffer before use, as air bubbles could block the column.
- Place column in the magnetic field of a suitable MACS Separator. For details refer to the respective MACS Column data sheet.
- (Optional) Place Pre-Separation Filter (70 µm) on top of the column to remove clumps which may clog the column.
▲ Note: Moisten Pre-Separation Filter with AstroMACS Separation Buffer before use. - Prepare column by rinsing with 500 µL of AstroMACS Separation Buffer.
- Apply cell suspension onto the column. Collect flow-through containing unlabeled cells.
- Wash column with 3×500 µL of AstroMACS Separation Buffer. Collect unlabeled cells that pass through and combine with the flow-through from step 4. This is the ACSA-2– cell fraction.
▲ Note: Perform washing steps by adding buffer aliquots as soon as the column reservoir is empty. - Remove column from the separator and place it on a suitable collection tube.
- Pipette 1 mL of AstroMACS Separation Buffer onto the column. Immediately flush out the magnetically labeled cells by firmly pushing the plunger into the column. This is the ACSA-2+ cell fraction.
- To increase the purity of ACSA-2+ cells, it is recommended to enrich the positive fraction over a second MS Column. Repeat the magnetic separation procedure as described in steps 1 to 7 using a new column.
- Take aliquots of positive and negative fraction and proceed to section "Flow cytometric analysis".
Magnetic separation with the autoMACS® Pro Separator
- Refer to the respective user manual for instructions on how to use the autoMACS Pro Separator.
- Use AstroMACS Separation Buffer. Buffers used for operating the autoMACS Pro Separator should have a temperature of ≥10 °C.
- Prepare and prime the instrument.
- Apply tube containing the sample and provide tubes for collecting the labeled and unlabeled cell fractions. Place sample tube in row A of the tube rack and the fraction collection tubes in rows B and C.
- For a standard separation choose the following program:
Positive selection: Possel
Collect positive fraction in row C of the tube rack. This fraction represents the ACSA-2+ cells. - (Optional) Collect negative fraction in row B of the tube rack. This fraction represents the ACSA-2– cells.
- Take aliquots of positive and negative fraction and proceed to section "Flow cytometric analysis".
- The recommended antibody dilution for labeling of cells is 1:10 for up to 1×106 cells/50 μL of D-PBS/BSA buffer.
- Volumes given below are for up to 1×106 nucleated cells. When working with fewer than 1×106 cells, use the same volumes as indicated. When working with higher cell numbers, scale up all reagent volumes and total volumes accordingly (e.g. for 2×106 nucleated cells, use twice the volume of all indicated reagent volumes and total volumes).
- (Optional) For analysis take 100 µL of positive and negative fraction. It is recommended to also analyze 20 µL of the original fraction.
- Resuspend up to 1×106 nucleated cells per 45 μL of D-PBS/BSA buffer.
- Add 5 μL of ACSA-2 Antibody, anti-mouse, APC.
- Mix well and incubate for 10 minutes in the dark in the refrigerator (2−8 °C).
▲ Note: Higher temperatures and/or longer incubation times may lead to non-specific cell labeling. Working on ice requires increased incubation times. - Wash cells by adding 1 mL of D-PBS/BSA buffer and centrifuge at 300×g for 10 minutes. Aspirate supernatant completely.
- Resuspend cell pellet in a suitable amount of D-PBS/BSA buffer for analysis by flow cytometry, e.g., using the MACSQuant® Analyzer 10.
- Plate 1×105 cells in 50 µL of pre-warmed prepared AstroMACS Medium as a drop in the middle of each well of a 24-well plate which has been coated overnight (refer to section “Things to prepare in advance of tissue dissociation and cell culture“).
- Let the cells settle down for 30 minutes at 37 °C in the incubator.
- Carefully add 450 µL of prepared AstroMACS Medium to each well.
- Maintain the culture by replacement of 50% of prepared medium every other day.
▲ Note: Cells loosely attach after the first days of cultivation. Therefore, a cultivation period of approximately one week is recommended.
Things to prepare in advance
Staining buffer: Prepare a solution containing autoMACS® Running Buffer with FcR Blocking Reagent, mouse in a ratio of 1:10, e.g., add 1 mL FcR Blocking Reagent to 9 mL autoMACS Running Buffer.
- Wash cells 3× with PBS.
- Fix cells with 2% PFA for 10 minutes at room temperature.
- Wash cells 3× with PBS.
▲Note: Fixed cells can be stored in azide-containing buffer at 2–8 °C for up to one week. - Add staining buffer (see section "Things to prepare in advance") and incubate for 10 minutes at room temperature.
- Discard staining buffer.
- Add primary antibody in staining buffer to the cells with a final concentration of 1–5 μg/mL and incubate at room temperature in the dark for 10 minutes.
- Wash cells 3× with autoMACS Running Buffer.
- Add a corresponding secondary antibody in staining buffer to the cells and incubate at room temperature in the dark for 10 minutes.
- Wash cells 3× with autoMACS Running Buffer.
▲Note: For co-staining with additional antibodies repeat steps 6–9. - Store cells in autoMACS Running Buffer.
- Cells are now ready for immunofluorescence microscopy.
▲Note: Samples can be stored at 2–8 °C in the dark for up to one week.
▲Note: When working with cells cultured on coverslips, the coverslips need to be mounted onto slides before imaging.