Recombinant SARS-CoV-2 Spike-Prot (HEK)-Biotin, Streptavidin, PE, and Anti-PE MicroBeads UltraPure are available as single products or all-in-one in the SARS-CoV-2 Spike B Cell MicroBead Kit, human (# 130-128-031).
Enrichment of SARS-CoV-2–specific B cells using recombinant SARS-CoV-2 proteins
This application protocol describes the preparation of tetramer solutions, the labeling, and the enrichment of SARS-CoV-2–specific B cells using recombinant SARS-CoV-2 spike proteins.
Preparation of PEB buffer
Prepare a solution containing phosphate-buffered saline (PBS), pH 7.2, 0.5% bovine serum albumin (BSA), and 2 mM EDTA by diluting MACS® BSA Stock Solution (# 130-091-376) 1:20 with autoMACS® Rinsing Solution (# 130-091-222). Keep buffer cold (2−8 °C). Degas buffer before use, as air bubbles could block the column.
Preparation of spike-tetramer-PE solution
The following protocol is an example when using Streptavidin, PE. Other streptavidin conjugates can be used as well. Always check the concentration of the stock beforehand and adapt the protocol accordingly.
For the preparation of the spike-tetramer-PE solution, Recombinant SARS-CoV-2 Spike-Prot (HEK)-Biotin was conjugated to Streptavidin, PE (refer to table 1).
▲ Note: Always prepare the spike-tetramer solution freshly before the use. It can be stored for up to 24 hours at 2–8 °C protected from light.
- Resuspend Recombinant SARS-CoV-2 Spike-Prot (HEK)-Biotin in deionized, sterile-filtered water to a final concentration of 0.1 mg/mL (e.g. use 250 µL water for 25 µg protein).
▲ Note: To avoid repeated freeze-thaw cycles prepare working aliquots from the stock solution of Recombinant SARS-CoV-2 Spike-Prot (HEK)-Biotin. Store the working aliquots at –70 °C. Once thawed the protein can be stored for up to three days at 4 °C. - Dilute Streptavidin, PE to a concentration of 50 µg/mL in PEB buffer.
- Mix Recombinant SARS-CoV-2 Spike-Prot (HEK)-Biotin, Streptavidin, PE, and PEB buffer carefully as indicated in table 1 and incubate for 15 minutes at room temperature.
Each test indicated in table 1 corresponds to 5×106 B cells (or 107 PBMCs). When working with less than 5×106 B cells (or 107 PBMCs), use the same volumes as indicated for one test. When working with more than 5×106 B cells (or 107 PBMCs), scale up all reagent volumes accordingly.
Table 1: Volumes needed for the spike-tetramer-PE solution.
| No. of tests | Recombinant SARS-CoV-2 Spike-Prot (HEK)-Biotin (0.1 mg/mL) | Streptavidin, PE (50 µg/mL) | PEB buffer |
| 1 | 3 µL | 0.6 µL | 1.4 µL |
| 5 | 15 µL | 3 µL | 7 µL |
| 10 | 30 µL | 6 µL | 14 µL |
| 20 | 60 µL | 12 µL | 28 µL |
Enrichment of CD19+ cells
B cells must be enriched from single-cell suspension of peripheral blood mononuclear cells (PBMCs) using the REAlease® CD19 MicroBead Kit (# 130-117-034) accordingly to the data sheet including removal of the REAlease Complex.
Magnetic labeling
- CD19+ cells were enriched from single-cell suspension of peripheral blood mononuclear cells (PBMCs) of COVID-19 convalescent individuals using the REAlease CD19 MicroBead Kit. All data show CD19+ cells after freezing and thawing.
- Volumes for magnetic labeling given below are for up to 5×106 total B cells. When working with fewer than 5×106 B cells, use the same volumes as indicated. When working with higher cell numbers, scale up all reagent volumes and total volumes accordingly (e.g. for 107 total B cells, use twice the volume of all indicated reagent volumes and total volumes).
- Determine cell number.
- Centrifuge cell suspension at 300×g for 10 minutes. Aspirate supernatant completely.
- Resuspend cell pellet in 100 µL of PEB buffer per 5×106 total B cells. Add 10 µL of spike-tetramer-PE and incubate for 30 minutes at 2–8 °C. Aspirate supernatant completely.
- Wash cells by adding 1–2 mL of PEB buffer per 106 total B cells and centrifuge at 300xg for 10 minutes. Aspirate supernatant completely.
- Resuspend cell pellet in 160 µL of PEB buffer per 106 total B cells.
- Add 40 µL of Anti-PE MicroBeads UltraPure (# 130-105-639) per 106 total B cells.
- Mix well and incubate for 15 minutes in the refrigerator (2–8 °C).
- Wash cells by adding 1−2 mL of buffer per 10⁶ total B cells and centrifuge at 300×g for 10 minutes. Aspirate supernatant completely.
- Resuspend up to 107 cells in 500 μL of buffer.
▲ Note: For higher cell numbers, scale up buffer volume accordingly. - Proceed to magnetic separation.
Magnetic separation
- Always wait until the column reservoir is empty before proceeding to the next step.
Magnetic separation with MS Columns (# 130-042-201)
- Place column in the magnetic field of a suitable MACS Separator. For details refer to the respective MACS Column data sheet.
- Prepare column by rinsing with 500 μL of buffer.
- Apply cell suspension onto the column. Collect flow-through containing unlabeled cells.
- Wash column with 3×500 μL of buffer. Collect unlabeled cells that pass through and combine with the flow-through from step 3.
▲ Note: Perform washing steps by adding buffer aliquots as soon as the column reservoir is empty. - Remove column from the separator and place it on a suitable collection tube.
- Pipette 1 mL of buffer onto the column. Immediately flush out the magnetically labeled cells by firmly pushing the plunger into the column.
You have previously chosen International as your location.
What do you want to do?