Immunophenotyping of regulatory T cells from mouse spleen using flow cytometry
MBTP 19 = Miltenyi Biotec-tested panel 19
This application protocol describes the flow cytometric analysis of regulatory T cells (Tregs) after spleen dissociation from healthy C57BL/6 mice. Mouse spleens are easily dissociated using the gentleMACS® Dissociators to quickly obtain viable single cell suspensions ready for flow cytometric analysis.
- Viobility Fixable Dye was reconstituted in advance. The vial was warmed up to room temperature to avoid water condensation. One vial of lyophilized Viobility Fixable Dye was reconstituted by addition of 100 µL anhydrous DMSO to the dye vial and mixed until completely dissolved. The solution was aliquoted and stored at –20 °C under anhydrous (desiccant) conditions and protected from light for up to one month.
- Volumes given below were for up to 107 nucleated cells. When working with fewer than 107 cells, use the same volumes as indicated. When working with higher cell numbers, scale up all reagent volumes and total volumes accordingly (e.g. for 2 × 107 nucleated cells, use twice the volume of all indicated reagent volumes and total volumes).
- Cell number was determined.
- Cells were washed by addition of 1 mL of 1× PBS and centrifuged at 300 × g for 10 minutes. Supernatant was aspirated completely.
- Cells were resuspended in 100 µL of 1× PBS.
- 1 µL of Viobility Fixable Dye was added.
- Samples were mixed well and incubated for 15 minutes in the dark at room temperature.
▲Note: Higher temperatures and/or longer incubation times may lead to non-specific cell labeling. Working on ice requires increased incubation times. - Cells were washed by addition 1 mL PEB buffer and centrifuged at 300 × g for 10 minutes. Supernatant was aspirated completely.
- Step 6 was repeated.
- Surface staining was performed.
Surface staining
- Volumes given below were for up to 106 nucleated cells. When working with fewer than 106 cells, use the same volumes as indicated. When working with higher cell numbers, scale up all reagent volumes and total volumes accordingly (e.g. for 2 × 106 nucleated cells, use twice the volume of all indicated reagent volumes and total volumes).
- Cell number was determined.
- Cells were centrifuged at 300×g for 10 minutes. Supernatant was aspirated completely.
- A master mix with all antibodies was prepared according to the dilutions mentioned in the respective antibody data sheets.
- 100 µl antibody master mix was added to the cells.
- Cells were resuspended and incubated for 10 minutes in the dark at +4 °C.
- Cells were washed by addition of 1 mL of PEB buffer and centrifuged at 300 × g for 5 minutes at +4 °C. Supernatant was aspirated completely.
- Intracellular staining was performed.
Intracellular staining
- Reagents were prepared freshly. Failure to do so may lead to sub-optimal results.
- The required total buffer volumes were calculated beforehand. Volumes depend on the number of cells to be analyzed as well as the number of tests to be performed. For more information, please refer to the FoxP3 Antibody data sheet.
- Fixation and Permeabilization solution was prepared by diluting 1:3 the Fixation/Permeabilization Solution 1 with the Fixation/Permeabilization Solution 2.
- 1× solution of Permeabilization Buffer was prepared by diluting the 10× Permeabilization buffer with deionized or distilled water.
▲Note: Before preparing the dilution make sure the buffer does not contain any precipitates. - Cells previously stained for surface markers were resuspended in 1 mL of cold, freshly prepared Fixation and Permeabilization Solution.
- Cells were mixed well and incubated for 30 minutes in the dark at +4 °C.
- Cells were washed by adding 1 mL of cold buffer per 106 cells and centrifuged at 300×g for 5 minutes at +4 °C. Supernatant was aspirated completely.
- Cells were washed by adding 1 mL of cold 1× Permeabilization Buffer and centrifuged at 300×g for 5 minutes at +4 °C. Supernatant was aspirated completely.
- Cells were resuspended in 1× Permeabilization Buffer and the corresponding volume of FoxP3 Antibody according to the dilution mentioned in the respective data sheet was added.
- Cells were mixed well and incubated for 30 minutes in the dark at +4 °C.
- Cells were washed by adding 1 mL of cold 1× Permeabilization Buffer and centrifuged at 300×g for 5 minutes at +4 °C. Supernatant was aspirated completely.
- Cells were resuspended in 100 µL of 1× Permeabilization Buffer and flow cytometric analysis was performed using the MACSQuant® Analyzer.
7 products found
|
For research use only
REA625
APC, PE-Vio 770, PE, Biotin
FC, IF, IHC, MICS
EUR 60,00
(excl. tax)
For research use only
For research use only
ICFC
30 µg in 200 µL
(excl. tax)
For research use only
For research use only
FC, MICS, IF, IHC
30 µg in 200 µL
(excl. tax)
For research use only
For research use only
FC
30 µg in 200 µL
(excl. tax)
For research use only
For research use only
FC
30 µg in 200 µL
(excl. tax)
For research use only
For research use only
for 100 tests
(excl. tax)
For research use only
For research use only
FC
30 µg in 200 µL
(excl. tax)
You have previously chosen International as your location.
What do you want to do?