Preparation of MACSpep single peptides for peptide loading on MHC MACSimers


This application protocol describes the preparation of lyophilized MACSpep single peptides for loading on MHC MACSimers to analyze antigen-specific T cells. Besides peptide preparation, it provides important technical advice and resources for the determination of the optimum peptide loading concentration for each individual application to ensure efficient peptide-MHC loading and antigen-specific T cell staining.

Protocol

  • Spin down the vial briefly before opening.
  • Dissolve the pellet by adding 100% DMSO at room temperature according to table 1. Vortex briefly until all lyophilized powder is dissolved.
    ▲ Note: Information on defining the optimum peptide concentration can be found in sections Tips & tricks for peptide loading and Resources.
  • Centrifuge at ≥800×g for 30 seconds.
  • Aliquot the solution in appropriate volumes to avoid repeated freeze-thaw cycles.
  • Close vials tightly and store at –20 °C.
    ▲ Note: It is recommended to use the dissolved MACSpep peptide within 6 months.

Table 1: Recommended volumes for dissolving MACSpep peptides.

 Final peptide stock concentration (mmol/L)Final peptide-loading concentration (µmol/L)DMSO volume (µL)
Recommended standard concentration1020020
Alternative concentrations, e.g., for high-affinity peptides or specific peptides with poor water solubility510040
2.55080
1.2525160
Lowest recommended concentration for peptides with poor water solubility0.1252.51600

Please note that there are a few MACSpep Single Peptide sequences that are very difficult to dissolve in aqueous buffer due to their amino acid sequence and other biochemical properties. For these sequences, it is recommended to buy the peptide-loaded MHC MACSimer version if available, as the peptide-loading using MHC MACSimer FleX Kits might not be feasible.

Table 2: MACSpep Single Peptides not recommended for MHC MACSimer peptide-loading.

MACSpep Single Peptide sequences that are not recommended for peptide-loading using
MACSimer FleX Kits*
Recommended peptide-loaded
MHC MACSimer reagent
MACSpep EBV LMP2a (FLYALALLL) HLA-A*02
(# 130-134-318)
MHC MACSimer A*0201 EBV LMP2a (FLYALALLL), human (# 130-134-621)
MACSpep EBV LMP2a (CLGGLLTMV) HLA-A*02
(# 130-134-316)
MHC MACSimer A*0201 EBV LMP2a (CLGGLLTMV), human (# 130-134-622)
MACSpep EBV LMP2a (PYLFWLAAI) HLA-A*24
(# 130-134-348)
MHC MACSimer A*2402 EBV LMP2a (PYLFWLAAI), human (# 130-134-633)
MACSpep KRAS G12V (KLVVVGAVGV) HLA-A*02
(# 130-136-064)
MHC MACSimer A*0201 KRAS-G12V (KLVVVGAVGV), human (# 130-136-355)
MACSpep NY-ESO-1 (SLLMWITQC) HLA-A*02
(# 130-134-555)
MHC MACSimer A*0201 NY-ESO-1 (SLLMWITQC), human (# 130-135-302)
MACSpep NY-ESO-1 (SLLMWITQV) HLA-A*02
(# 130-134-554)
Currently not available
MACSpep IAV MP1 (GILGFVFTL) HLA-A*02
(# 130-136-110)
MHC MACSimer A*0201 IAV MP1 (GILGFVFTL), human (# 130-134-624)
*MACSpep Single Peptides sequences can still be used for T cell expansion purposes.

A short guide for peptide selection and loading can be downloaded here: Peptide loading using MHC MACSimer Flex Kits

Shop required products for this application protocol

151 products found

|

You have previously chosen International as your location.
What do you want to do?